PoolCalc.

Pool volume calculator

The number every other pool calculation depends on: how much water you actually have, in US gallons and cubic feet, from the shape and depth you can measure with a tape.

Default result

18,193 gallons

rectangle · 4.75 ft average depth · 512 sq ft surface

Volume 18,193 gal 2,432 cu ft × 7.48 gal per cu ft
Volume in litres 68,867 L 1 US gallon = 3.785 L
Surface area 512 sq ft Water surface, not the deck
Average depth 4.75 ft (3.5 + 6.0) ÷ 2
Gallons per foot of depth 3,830 gal Useful for partial drains and top-ups
  • Volume = surface area × average depth × 7.48 gallons per cubic foot. The 7.48 is the definition of the US liquid gallon (231 cubic inches).
  • Average depth is the shallow end plus the deep end, divided by two — the same approximation PoolMath uses for a sloping floor.

Before you dose

  • The average-depth method treats the slope as a straight line. Pools with a deep well and a long shallow shelf hold less water than this.
  • Every chemical dose on this site is only as good as the volume. If you can, read the meter before and after filling to check the figure once.

Other ways to do it

  • 16,373 gal — 10% lower: a sloped hopper, steps and a sun shelf take space the box formula gives back.
  • 19,102 gal — 5% higher: add for a spa, a catch basin or plumbing you are also treating.

What the default pool works out to

The form starts with a 16 × 32 ft rectangle, 3.5 ft at the shallow end and 6 ft at the deep end. That is 512 sq ft of water surface and an average depth of 4.75 ft, so the pool holds 2,432 cubic feet — about 18,193 US gallons. Every chemical calculator on this site uses that figure the same way: dose = concentration × volume, so a volume that is 10% wrong makes every dose 10% wrong.

The interesting part is not the multiplication. It is deciding which measurements to put in. A pool is not a box: most have a slope, a hopper, steps, a bench or a sun shelf, and the waterline you measure at the deck is a little longer than the water surface once the coping overhangs.

The formula, shape by shape

ShapeSurface areaGallons
Rectangularlength × widtharea × average depth × 7.48
Roundπ × (diameter ÷ 2)²area × average depth × 7.48
Ovalπ × length × width ÷ 4area × average depth × 7.48
Kidney0.45 × length × widtharea × average depth × 7.48

The 7.48 is not a pool industry convention; it is the definition of the US liquid gallon. One gallon is 231 cubic inches, one cubic foot is 1,728 cubic inches, and 1,728 ÷ 231 = 7.4805. The litre figure in the result uses 3.785 litres per US gallon, the conversion in the NIST guide to SI units.

Average depth is the shallow end plus the deep end, divided by two. It is the same approximation PoolMath uses for a sloping floor, and it is good enough for dosing because the error is usually smaller than the error in a test strip.

Where the number breaks down

A rectangular pool with a constant depth is the easy case, and the answer is close to exact. Everything else carries an assumption you should know about:

None of this makes the calculator useless. It makes the result a better starting point than a round number from a brochure, and it tells you when to stop trusting it. If you are about to add 400 lb of salt, the difference between 18,000 and 20,000 gallons is 45 lb of salt — worth ten minutes with a tape.

How to measure a pool you did not build

  1. Length and width at the waterline. Hook the tape on the coping, not the tile, and read to the same point on the far side.
  2. Depth in three places. Shallow end, middle, deep end. If the middle is not the average of the ends, the floor is not a straight slope and the average-depth method will be off.
  3. Deduct what is not water. Steps, a diving rock, a sun shelf. Estimate the footprint and multiply by the water depth over it.
  4. Check with the water meter, once. Read the meter before and after a fill, subtract normal household use, and convert cubic feet to gallons at 7.48. That number is your real volume.

Once you have the volume, the rest of the site follows from it: the free chlorine calculator doses by gallons, the salt calculator converts a ppm target into bags, and the filter calculator turns volume and run time into a flow rate. The gallon chart has common sizes already worked out if you want a cross-check.

Frequently asked

How many gallons is a 16 × 32 pool?

At an average depth of 4.75 ft a 16 × 32 rectangular pool holds about 18,200 US gallons. That is 512 sq ft × 4.75 ft × 7.48 gal per cubic foot. A 16 × 32 with a constant 4 ft depth holds about 15,300 gallons.

How do I work out the average depth?

Add the shallow-end depth to the deep-end depth and divide by two. A pool that runs 3.5 ft to 6 ft averages 4.75 ft. This treats the floor as a straight slope, which is close for most pools but overstates a pool with a long shallow shelf.

Is 7.48 gallons per cubic foot exact?

Yes for the US liquid gallon: one gallon is 231 cubic inches, and 1,728 cubic inches make a cubic foot, so 1,728 ÷ 231 = 7.4805. The UK imperial gallon is different and is not used here.

Why does the pool store say my pool is 20,000 gallons?

Pool volumes are usually rounded to the nearest thousand, and many stores use a rule of thumb rather than your measurements. A rounded number is fine for a chlorine range but not for a salt or stabilizer dose, where a 10% error carries through.

Does a spa or tanning shelf change the answer?

Yes. A built-in spa, a deep catch basin or a large sun shelf holds water the box formula does not see. Work each part out separately and add the volumes together, or meter the water when you fill.

Where these numbers come from

Figures that come from our own arithmetic rather than a published guide are marked house rule on the method page. No price is shown anywhere on this site.

Related: free chlorine dose · salt · filter size · common pool gallon chart