CYA (stabilizer) calculator
The stabilizer dose to raise cyanuric acid, or the water to replace to bring it down — because CYA is the one number that quietly changes every chlorine dose you make.
Default result
1.3 lb of stabilizer
Raise CYA 30 → 40 ppm in 15,000 gal
| CYA now | 30 ppm | From your test |
| Target | 40 ppm | Midpoint of the recommended band |
| Stabilizer to add | 1.3 lb | 20.0 oz by weight |
| Per 10,000 gal | 0.8 lb | For a quick cross-check |
- CYA is dosed by mass exactly like salt: pounds = ppm × gallons × 8.34 ÷ 1,000,000.
- The 30–60 ppm band is the published target for a liquid-chlorine pool; 60–90 is the band for a salt pool, where the cell adds chlorine slowly all day.
Before you dose
- Put granular stabilizer in a sock or a mesh bag in the skimmer or in front of a return. It can take 24 to 48 hours to dissolve and it will bleach a vinyl liner if it sits on it.
- Do not backwash for a week after adding it, or you will send the undissolved part down the drain.
- CYA only leaves the pool by dilution. If you overshoot, the fix is a partial drain, not another chemical.
Other ways to do it
- 1.0 lb — Add 80% now, retest in two days, then top up. CYA tests read in steps of 10, so the last pound is guesswork.
- Liquid stabilizer — Faster and easier to measure, but you pay for the water it is dissolved in.
The default pool: 15,000 gallons, 30 → 40 ppm
Ten ppm of cyanuric acid in 15,000 gallons is 1.25 lb of stabilizer, about 20 oz. The arithmetic is the same mass balance as salt: 10 × 15,000 × 8.34 ÷ 1,000,000 = 1.25 lb. It is a small amount, and it is easy to overshoot, so the alternatives suggest adding 80% and retesting rather than chasing the last quarter pound.
The direction matters. CYA is easy to add and hard to remove. If you are at 30 and want 40, one sock of stabilizer does it. If you are at 80 and want 50, no chemical will help; you replace about 37% of the water.
What CYA does
Cyanuric acid binds free chlorine into a reserve form that sunlight cannot destroy. Without it, a pool in full sun can lose most of its chlorine in a few hours. With it, the same dose lasts through the day.
The catch is that bound chlorine is not disinfecting. As CYA rises, a larger share of the measured FC is in reserve, so you need a higher FC number to keep the same active concentration. That is the entire reason the FC/CYA chart exists, and why "3 ppm" is a strong pool at CYA 30 and a weak one at CYA 90.
| CYA | Liquid-chlorine FC target | Where it suits |
|---|---|---|
| 20 – 30 | 3 – 6 ppm | Indoor pool, or a pool with little sun |
| 40 – 50 | 5 – 8 ppm | Typical outdoor liquid-chlorine pool |
| 60 – 70 | 7 – 10 ppm | Hot, sunny climate; salt pool lower end |
| 80 – 90 | 9 – 12 ppm | Salt pool upper end; hard to shock |
The bands are community practice from Trouble Free Pool, not a regulation. Your local code may set different limits for a public pool, and a public pool is a different problem from a family pool.
Raising CYA without overshooting
- Test first, and trust the step size. The common turbidity test reads in steps of 10 ppm. A reading of "40" means somewhere around 35 to 45.
- Add 80% of the calculated dose. Put granular stabilizer in a sock or mesh bag in the skimmer or in front of a return.
- Squeeze the sock every few hours to speed it up. Do not dump the granules into the pool; they can bleach a liner where they land.
- Wait 24 to 48 hours, then retest. Add the rest only if the reading is still below target.
- Do not backwash for a week. Undissolved stabilizer sitting in the filter will go to waste.
Lowering CYA: the dilution maths
CYA is not volatile and does not break down quickly at normal chlorine levels. Evaporation leaves it behind, so topping up a pool does not dilute it. The only practical reduction is replacing water:
fraction to replace = (current − target) ÷ current
Going from 80 to 50 ppm means (80 − 50) ÷ 80 = 37.5%. In a 15,000 gallon pool that is 5,625 gallons. Going from 100 to 40 means 60%, which is a big drain and a big refill — and a reminder to test CYA before adding another trichlor tab.
Drain in stages if the pool is vinyl-lined or the water table is high. Emptying a pool can float a liner or lift a shell, and the risk is not worth the time saved. Check local rules before sending pool water to a storm drain.
How pools end up over-stabilized
- Trichlor tablets. Every 3-inch tab adds CYA as well as chlorine. A pool on tabs for a full season can climb 30 to 50 ppm without anyone adding stabilizer on purpose.
- Dichlor shock. The same problem in powder form, and it is often sold as "shock" without the CYA warning on the front of the tub.
- Following a "add stabilizer" instruction without testing. CYA does not leave the pool, so a dose based on a guess stays in the water.
- Not accounting for splash-out. A pool with a lot of splashing and backwashing loses CYA faster than a covered pool, so the same schedule does not fit both.
High CYA is not a chlorine problem. If the pool will not hold chlorine and the CYA is 90, adding more chlorine is treating the symptom. Dilute first, then maintain the FC target for the new level.
What this calculator cannot tell you
- Your exact CYA. The turbidity test is coarse and the reagent has a shelf life. A reading in steps of 10 is normal.
- Whether the test is valid. A CYA test at very high chlorine or cloudy water can read falsely. Fix the water first.
- The effect on a salt cell. Higher CYA reduces chlorine demand, which lets the cell run less, but it also makes a SLAM harder. There is a trade-off, not a free win.
- Local discharge rules. Draining a pool is regulated in some places, especially for salt or chlorinated water.
The chlorine calculator uses this number directly, and the shock calculator shows what a high CYA does to the dose. If you are about to switch to a salt pool, the salt page covers the other half of the chemistry.
Frequently asked
How much stabilizer to raise CYA by 10 ppm?
In 15,000 gallons, 10 ppm of CYA takes about 1.25 lb (20 oz) of granular stabilizer. The dose is 8.34 lb per 1,000,000 lb of water per ppm, so it scales with volume.
What CYA should my pool have?
30 to 60 ppm for a liquid-chlorine pool, and 60 to 90 ppm for a saltwater chlorine generator pool. Indoor pools usually run 20 to 30 ppm because there is little sunlight to protect against.
How do I lower CYA?
Dilute. CYA does not evaporate and is not consumed at normal chlorine levels, so replacing part of the water is the only practical answer. Going from 80 to 50 ppm means replacing about 37% of the water.
How long does stabilizer take to dissolve?
Granular stabilizer in a sock can take 24 to 48 hours, especially in cold water. Do not backwash for a week after adding it, or you will send the undissolved part to waste.
Does CYA go away over winter?
Slowly. You may lose 5 to 10 ppm a month in summer to splash-out, backwashing and oxidation. It does not evaporate with the water, so a pool that only loses water to evaporation keeps its CYA.
Where these numbers come from
- The Free Chlorine and Cyanuric Acid Relationship — Trouble Free Pool, checked Nov 20, 2026 (published Jan 18, 2019)
- Liquid-chlorine FC targets by CYA: 20 ppm CYA → 3–5 ppm FC; 30 → 4–6; 40 → 5–7; 50 → 6–8; 60 → 7–9; 70 → 8–10; 80 → 9–11; 90 → 10–12; 100 → 11–13.
- Minimum FC by CYA: 20 → 2; 30 → 2; 40 → 3; 50 → 4; 60 → 5; 70 → 5; 80 → 6; 90 → 7; 100 → 8 ppm.
- SLAM (shock) level by CYA: 20 → 10; 30 → 12; 40 → 16; 50 → 20; 60 → 24; 70 → 28; 80 → 31; 90 → 35; 100 → 39 ppm.
- PoolMath — pool chemistry calculator — Trouble Free Pool, checked Nov 20, 2026
- If depth varies, PoolMath uses the average of the shallow-end and deep-end depths.
- Irregular shapes are approximated by an average length and width using the rectangular formula.
- The calculator offers 10% and 12.5% liquid chlorine, 73% cal hypo and 56% dichlor among its chlorine sources.
Figures that come from our own arithmetic rather than a published guide are marked house rule on the method page. No price is shown anywhere on this site.
Related: free chlorine · shock · salt · pool volume