Free chlorine calculator
How much chlorine to pour, in the units on the bottle, from the free chlorine reading you already have and the stabilizer level that decides what "enough" means.
Default result
77 fl oz of 10% liquid
FC 2.0 → 6.0 ppm in 15,000 gal · CYA 40 ppm
| Target FC for CYA 40 ppm | 5.0 – 7.0 ppm | Never below 3.0 ppm |
| Free chlorine now | 2.0 ppm | From your test kit |
| Chlorine to add | 4.0 ppm | Target minus the reading |
| Dose | 77 fl oz | 10% liquid chlorine |
| Jugs | 1 × 1 gal | Buy whole jugs; measure the part jug |
- At CYA 40 ppm the published target range is 5.0–7.0 ppm FC, so the midpoint is 6.0 ppm.
- Dose = ppm rise × gallons × 3.785 L/gal ÷ (available chlorine in the product). That is mass balance, not a rule of thumb.
- Use the manual target if you are dosing toward the top of the range before a hot, busy weekend.
Before you dose
- Add chlorine at dusk or on a cloudy day, with the pump running. Sunlight destroys most of a dose within a few hours.
- Pour liquid chlorine slowly in front of a return, then brush. Never mix it with acid, or with a different chlorine product, in the same container.
- Retest 30 to 60 minutes after the pump has mixed it. The dose is an estimate; the test is the answer.
Other ways to do it
- 7.0 ppm — The top of the range: before a party, a heat wave, or a day you cannot test.
- 3.0 ppm — The floor, not a target. Do not plan to sit here.
The default pool: 15,000 gallons, 2 ppm, CYA 40
At 40 ppm cyanuric acid the published target band is 5 to 7 ppm free chlorine, so the calculator aims at the midpoint, 6 ppm. The pool is at 2, so it needs 4 ppm. In 15,000 gallons that is 77 fl oz of 10% liquid chlorine — about 0.6 gallon, or a little over half a jug. The same 4 ppm would take 61 fl oz of 12.5%, 1.1 lb of 73% cal hypo, or 1.4 lb of 56% dichlor.
Notice what did not enter the calculation: the size of the pool alone. A 15,000 gallon pool at 6 ppm needs no chlorine at all. A 5,000 gallon pool at 1 ppm with CYA 80 needs a surprising amount. The reading and the stabilizer are the inputs that matter; the volume only scales the answer.
Why the target moves with CYA
Cyanuric acid binds most of the free chlorine in the water into a reserve form. That reserve protects it from sunlight, which is why a stabilised pool holds chlorine through a sunny day, but it also means that only a small fraction of the measured FC is active. As CYA rises, you need a higher FC number to keep the same amount of active disinfectant.
That is the whole argument behind the FC/CYA chart, and it is why "1 to 4 ppm" from an old test kit label is not a target you can use without knowing CYA. The chart below is the liquid-chlorine column of the Trouble Free Pool chart, which is community practice rather than a regulation:
| CYA (ppm) | Minimum FC | Target FC |
|---|---|---|
| 20 | 2 | 3 – 5 |
| 30 | 2 | 4 – 6 |
| 40 | 3 | 5 – 7 |
| 50 | 4 | 6 – 8 |
| 60 | 5 | 7 – 9 |
| 70 | 5 | 8 – 10 |
| 80 | 6 | 9 – 11 |
| 90 | 7 | 10 – 12 |
| 100 | 8 | 11 – 13 |
Between rows the calculator interpolates linearly, because a test that reads in steps of 10 still leaves you between two rows. Above 90 ppm the honest advice is to dilute rather than dose: the target gets high enough that you are buying a lot of chlorine to satisfy a number.
What each product actually delivers
| Product | Available chlorine | 1 lb or 1 gal in 10,000 gal | Also adds |
|---|---|---|---|
| 10% liquid chlorine | 10% | 1 gal → 10 ppm | Salt, a little pH rise |
| 12.5% liquid chlorine | 12.5% | 1 gal → 12.5 ppm | Salt, a little pH rise |
| 73% cal hypo | 73% | 1 lb → 8.7 ppm | Calcium hardness, pH rise |
| 56% dichlor | 56% | 1 lb → 6.7 ppm | CYA, pH down |
The dose is mass balance: 1 ppm is 1 mg per litre, a US gallon is 3.785 litres, and the product label tells you what fraction of the weight or volume is available chlorine. The calculator treats liquid chlorine as weighing 1.0 kg per litre, which is close enough for a dose you will verify with a test 30 minutes later. Powders vary more between brands, so weigh them rather than scooping by volume.
How to add it without wasting it
- Test first. A FAS-DPD test gives you free chlorine and combined chlorine; a DPD colour match is coarser but usable.
- Dose at dusk. Sunlight can consume most of a dose within hours, especially at low CYA.
- Pour in front of a return with the pump running, then brush the walls. Never pour into the skimmer.
- Retest after 30 to 60 minutes. If the reading is lower than predicted, the demand was higher than the dose, not the arithmetic wrong.
- Log the reading and the dose. After two weeks you can see your pool's daily demand instead of guessing it.
Do not mix chlorine products. Acid and chlorine, cal hypo and dichlor, or two brands in one bucket can react violently. Add one product at a time, to the pool, with the pump running.
What this calculator cannot tell you
- Combined chlorine. A pool can read 3 ppm FC and still smell of chlorine because combined chloramines are high. If CC is above 0.5 ppm, the answer is oxidation, not more FC.
- Whether the water is safe. FC is one number. pH, alkalinity, calcium and cyanuric acid all change how the water behaves and how the chlorine feels.
- Algae. Green water needs the shock calculator and a filter that runs continuously, not a maintenance dose.
- Your test's accuracy. A strip that reads "2" may be 1 or 3. The dose inherits that error.
If you do not know the volume, start with the volume calculator. If you do not know CYA, the CYA page explains what the test is telling you and why the number matters more than the chlorine label.
Frequently asked
How much chlorine do I add to a 15,000 gallon pool?
It depends on the current reading and the CYA. At CYA 40 ppm the target is 5 to 7 ppm; to lift a 15,000 gallon pool from 2 to 6 ppm takes about 77 fl oz of 10% liquid chlorine, or 0.6 gallon. At CYA 80 the target doubles and so does the dose.
Should I use liquid chlorine, cal hypo or dichlor?
Liquid chlorine adds only chlorine and a little salt. Cal hypo adds calcium hardness and raises pH. Dichlor adds cyanuric acid, about 0.9 ppm of CYA for every 1 ppm of chlorine, which is the opposite of what most pools need. Liquid is the simplest daily choice.
Why does my pool need more chlorine than my neighbour’s?
Almost always CYA. The same 3 ppm free chlorine is strong in a pool with 30 ppm CYA and weak in one with 90 ppm, because more of it is bound to stabilizer. Shade, bather load and temperature matter too, but CYA is the big one.
Can I swim right after adding chlorine?
Wait until the pump has mixed it and a test shows the level is inside the normal range for your CYA. Liquid chlorine poured in front of a return mixes in about 30 minutes. Do not swim while the pool is at shock level.
Does the calculator work for a salt pool?
The dose maths is identical, but a salt pool normally makes its own chlorine and you would adjust the cell output or run time instead of pouring liquid. Use this page for a manual top-up or after a heavy bather load, and check the salt level separately.
Where these numbers come from
- The Free Chlorine and Cyanuric Acid Relationship — Trouble Free Pool, checked Nov 20, 2026 (published Jan 18, 2019)
- Liquid-chlorine FC targets by CYA: 20 ppm CYA → 3–5 ppm FC; 30 → 4–6; 40 → 5–7; 50 → 6–8; 60 → 7–9; 70 → 8–10; 80 → 9–11; 90 → 10–12; 100 → 11–13.
- Minimum FC by CYA: 20 → 2; 30 → 2; 40 → 3; 50 → 4; 60 → 5; 70 → 5; 80 → 6; 90 → 7; 100 → 8 ppm.
- SLAM (shock) level by CYA: 20 → 10; 30 → 12; 40 → 16; 50 → 20; 60 → 24; 70 → 28; 80 → 31; 90 → 35; 100 → 39 ppm.
- PoolMath — pool chemistry calculator — Trouble Free Pool, checked Nov 20, 2026
- If depth varies, PoolMath uses the average of the shallow-end and deep-end depths.
- Irregular shapes are approximated by an average length and width using the rectangular formula.
- The calculator offers 10% and 12.5% liquid chlorine, 73% cal hypo and 56% dichlor among its chlorine sources.
- NIST Guide to the SI, Special Publication 811, Appendix B: Conversion Factors — National Institute of Standards and Technology, checked Nov 20, 2026
- 1 US gallon = 3.785 412 L.
- 1 foot = 0.3048 m exactly.
- 1 cubic foot = 28.316 85 L.
Figures that come from our own arithmetic rather than a published guide are marked house rule on the method page. No price is shown anywhere on this site.
Related: shock dose · CYA · salt · pool volume