Pool salt calculator
Pounds of salt, 40 lb bags and the rise each bag gives you, from the salinity you measured to the level your chlorine generator wants.
Default result
75.1 lb of pool salt
600 ppm rise in 15,000 gal · 2 × 40 lb bags
| Salt now | 2,600 ppm | From your test |
| Target | 3,200 ppm | Inside the usual 2,700–3,500 band |
| Salt to add | 75.1 lb | 5.0 lb per 1,000 gal |
| 40 lb bags | 2 | Round up; part bags are hard to store |
| Rise per bag | 320 ppm | In this pool |
- 1 ppm in 1 gallon weighs 8.34 ÷ 1,000,000 lb, so pounds = ppm × gallons × 8.34 ÷ 1,000,000.
- That is the same mass-balance arithmetic PoolMath uses for salt; the only choice is the target.
Before you dose
- Add salt with the pump running and brush until it dissolves. Do not let it sit on a plaster floor or in a vinyl corner.
- Do not add salt within 24 hours of adding chlorine or acid, and never pour it into the skimmer.
- Test again after 24 hours before adding more. Cold water dissolves salt slowly and reads low for a day.
Other ways to do it
- 67.6 lb — If your strip reads low by about 10%, which is common in cold water.
- 3 bags — One spare bag for the season; salt is not the thing to run out of.
The default pool: 15,000 gallons, 2,600 → 3,200 ppm
The default is a 15,000 gallon pool sitting a little under target at 2,600 ppm, aiming at 3,200. The gap is 600 ppm, which works out at 75 lb of salt — two 40 lb bags, with about 5 lb left over. Each bag raises this pool by roughly 320 ppm, so the second bag lands you at about 3,240 ppm, comfortably inside the usual band.
Salt is one of the few pool chemicals where the arithmetic is almost exact. Salt does not evaporate, does not get consumed by the chlorine generator in any meaningful quantity, and does not react with much else in the water. If you know the volume and the current reading, the pounds follow directly.
The formula
One ppm is one pound of salt per million pounds of water. A US gallon of water weighs about 8.34 lb, so:
pounds = (target − current) × gallons × 8.34 ÷ 1,000,000
For the default: 600 × 15,000 × 8.34 ÷ 1,000,000 = 75.06 lb. The calculator rounds the bags up because a part bag is awkward to store and the last few pounds barely move the reading.
| Pool size | One 40 lb bag raises | Salt for +500 ppm |
|---|---|---|
| 10,000 gal | 480 ppm | 42 lb — about 1 bag |
| 15,000 gal | 320 ppm | 63 lb — 1.6 bags |
| 20,000 gal | 240 ppm | 83 lb — 2.1 bags |
| 25,000 gal | 192 ppm | 104 lb — 2.6 bags |
| 30,000 gal | 160 ppm | 125 lb — 3.1 bags |
Those figures assume the pool volume is right. A 20% error in volume is a 20% error in salt, which is why the volume calculator comes first. Salt is also the cheapest thing to overshoot slightly and the most annoying to overshoot badly, because the only fix is dilution.
What level should a salt pool run at?
There is no single national figure. Residential chlorine generator manuals typically specify a band somewhere between 2,700 and 3,500 ppm, and the cell will stop making chlorine below its own minimum. The default target of 3,200 ppm sits in the middle of that range, which gives you room for splash-out and rain without dropping below the cut-off.
The exact number for your system is in its manual, and it is worth reading rather than assuming. Some cells are happy at 2,700; others want 3,500 before they will run at full output. The calculator lets you type the target, so use the figure on your cell rather than the default if they disagree.
How to add salt without making a mess
- Test the water, not the cell display. A strip or a salinity meter is the reading that matters. The cell's own number is a conductivity estimate and drifts as the plates scale.
- Brush the floor first if it is plaster. Salt sitting in a pile on plaster can leave a mark; brushing spreads it before it dissolves.
- Pour along the deep end with the pump running. Add about half, brush, then add the rest. Do not dump it all in one spot.
- Wait 24 hours before retesting. Cold water dissolves salt slowly and reads low for a day. Adding more on the first reading is how pools end up at 4,000 ppm.
- Run the pump and the cell as usual. The cell needs moving water at the right salinity; it will not start making chlorine just because the salt is in the pool.
Do not use softened water as a shortcut. A water softener swaps calcium for sodium, but the chloride stays, so soft water can carry more salt than you expect. Test it before you use it to top up a salt pool.
What this calculator cannot tell you
- Whether the cell is working. Low chlorine output with correct salt is usually a scaled cell, a failing cell, low CYA or a short run time, not a salt problem.
- Your true salinity. Strips read in steps of 100 to 200 ppm and are affected by temperature. A meter is better; a laboratory test is better still.
- What the salt will do to a painted or natural-stone pool. Salt is corrosive to some finishes and to metal handrails. Ask before adding it to an older pool.
- Whether you should run a salt pool at all. The generator is a chlorine delivery method, not a different kind of water. pH and CYA still need managing.
Once the salt is right, the chlorine page covers the FC/CYA target the cell has to hit, and the CYA page explains why salt pools usually run a higher stabilizer level than liquid-chlorine pools.
Frequently asked
How many bags of salt for a 15,000 gallon pool?
To go from 2,600 to 3,200 ppm in 15,000 gallons you need about 75 lb, which is two 40 lb bags. One bag raises that pool by roughly 320 ppm.
Does salt evaporate?
No. Salt stays in the water when water evaporates, so topping up a pool does not lower salinity. Only splash-out, backwashing, draining and overflow reduce it.
Can I add salt and chlorine at the same time?
Do not add them at the same moment or in the same place. Add salt with the pump running and brush it until dissolved, and leave at least 24 hours before adding acid or a large chlorine dose.
Why does my salt cell say low salt when my test strip says fine?
A scaled cell reads low because the plates are coated. Clean the cell, retest the water, and only add salt if the water itself is low. Adding salt to a dirty cell makes the real level too high.
What salt should I use?
Plain water-softener or pool salt with no additives, no anti-caking blend and no iodine. Read the bag: iron, copper or a clarifier in the salt will stain a pool and upset the cell.
Where these numbers come from
- PoolMath — pool chemistry calculator — Trouble Free Pool, checked Nov 20, 2026
- If depth varies, PoolMath uses the average of the shallow-end and deep-end depths.
- Irregular shapes are approximated by an average length and width using the rectangular formula.
- The calculator offers 10% and 12.5% liquid chlorine, 73% cal hypo and 56% dichlor among its chlorine sources.
- NIST Guide to the SI, Special Publication 811, Appendix B: Conversion Factors — National Institute of Standards and Technology, checked Nov 20, 2026
- 1 US gallon = 3.785 412 L.
- 1 foot = 0.3048 m exactly.
- 1 cubic foot = 28.316 85 L.
- Pool & Spa Calculators — Pentair, checked Nov 20, 2026
- Pentair publishes a collection of pool and spa calculators for homeowners and professionals.
- The collection includes volume and other pool-math tools rather than a single all-purpose calculator.
Figures that come from our own arithmetic rather than a published guide are marked house rule on the method page. No price is shown anywhere on this site.
Related: free chlorine · CYA · pool volume · shock